antec-ax-series – Ringwood Digital Store

Antec AX85 ARGB ATX Gaming Case

RDSG — Mon, 13 Apr 2026 13:32:16 +0000

Wave Mesh Front Panel — Style and Substance

The AX85 sets itself apart with a ripple-patterned mesh front panel that goes beyond purely functional airflow design — the wave motif gives it a distinctive look without the bulk of a solid or glass front. Functionally, the large-area mesh allows cool air to pass into the chassis freely, feeding the three front-mounted intake fans without restriction. Dual dust filters — a magnetic unit on top and a flat filter at the bottom — make maintenance straightforward without tools, keeping intake quality high over time. It’s a front panel that holds its own aesthetically while never compromising on what matters.

Four ARGB Fans, Daisy-Chain Ready

Four 120mm ARGB fans come pre-installed out of the box — three at the front handling intake and one at the rear for exhaust — covering the primary airflow positions immediately. The front fans support daisy-chain synchronisation, letting you link them together via the lead fan and keep the ARGB cabling manageable. An onboard LED control button on the front I/O panel lets you cycle through lighting effects or switch them off without needing software. The chassis supports up to eight 120mm fans simultaneously, leaving space to add top or PSU shroud fans as the build demands.

Generous Hardware Clearances and Cooling Flexibility

The AX85 is built to accommodate serious hardware. GPUs up to 340mm fit comfortably with all front fans installed; remove the front fan bracket and that ceiling rises to 370mm, opening the door to high-end triple-slot cards. CPU tower coolers up to 160mm tall are supported, and the front panel takes radiators up to 360mm — making 240mm and 360mm AIO liquid coolers a straightforward fit. Storage is well covered with two 3.5″/2.5″ combo bays and two dedicated 2.5″ SSD bays. Cable management sits at 23mm behind the motherboard tray — tight but workable for a neat finish.

GPU Length Note: The 370mm GPU clearance figure applies only with the front fan bracket removed. With all three front fans installed, maximum GPU length is 340mm. Measure your card before building — most current-gen cards fall well within the 340mm limit, but flagship models can push longer.

PSU Length Note: Check the official Antec spec sheet for your specific PSU length limit with the HDD tray in place, as longer PSUs may require repositioning or removing the tray for a proper fit.

Key Highlights

Form Factor: Mid Tower (ATX / Micro-ATX / Mini-ITX)
GPU Clearance: Up to 340mm (with front fans) / Up to 370mm (without front fans)
CPU Cooler Clearance: Up to 160mm
Pre-Installed Fans: 4× 120mm ARGB (3 Front, 1 Rear)
Max Fan Support: Up to 8× 120mm simultaneously
Radiator Support: Front: 120 / 140 / 240 / 280 / 360mm | Top: 120 / 240mm | Rear: 120mm
Drive Bays: 2× 3.5″/2.5″ combo, 2× 2.5″ dedicated
Expansion Slots: 7
Front I/O: 2× USB 3.0, Headphone/Mic Combo Jack, LED Control Button
Side Panel: 4mm Tempered Glass
Dust Filters: Magnetic (top), flat filter (bottom)
Cable Management: 23mm rear clearance
Materials: Steel + Plastic
Dimensions: 393 × 205 × 485mm (D × W × H)
PSU: Not included (standard ATX)
Colour: Black

Proudly sold by the Ringwood Digital Store.

Antec AX27 RGB ELITE Gaming Case

RDSG — Fri, 10 Apr 2026 10:29:13 +0000

Full-Mesh Front Panel — Maximum Airflow by Design

The AX27 RGB Elite leads with one of its strongest attributes: a full-mesh front panel purpose-built for unrestricted airflow. Where solid or glass fronts create a bottleneck for intake, the AX27’s mesh design allows cool air to flow directly into the chassis with minimal resistance — feeding the three front-mounted fans and keeping temperatures stable under sustained gaming loads. This makes it a particularly strong pick for builders running warmer components who don’t want to compromise on airflow in exchange for aesthetics.

Four Pre-Installed RGB Fans — Lighting Without the Controller Tax

The AX27 ships ready to run with four pre-installed 120mm fixed RGB fans — three at the front and one at the rear — covering the most impactful airflow positions from the moment your build is complete. The fans deliver vivid colour lighting without requiring an external RGB controller or software configuration, keeping the initial setup straightforward. The case supports up to eight 120mm fans simultaneously, offering significant headroom for builders who want to expand their cooling setup over time, including front, top, rear, and bottom mounting positions.

Half-View Tempered Glass Side Panel — Style Where It Counts

Rather than a full-side glass panel, the AX27 RGB Elite features a half-view tempered glass side panel that frames the interior without fully exposing it. This design choice gives the case a more structured, purposeful aesthetic — putting your components and RGB fans on display while maintaining a solid upper section that contributes to the overall chassis rigidity. It’s a practical middle ground between a fully enclosed steel side and a full panoramic glass design.

Important Note: The pre-installed fans are fixed-colour RGB (FRGB) — not addressable ARGB. This means they emit a fixed colour and cannot be individually controlled or software-synced via motherboard ARGB headers. Lighting can be toggled using the front I/O LED button, but colour customisation per fan is not supported. If full ARGB control is a priority for your build, consider pairing with aftermarket ARGB fans.

Buyer Tip: GPU clearance drops to 295mm with front fans installed and 270mm with the rear fan in place. If you’re planning to run a longer graphics card (300mm+), check your GPU dimensions carefully before building — particularly if you intend to keep all fans mounted as shipped.

Key Highlights

Form Factor: Mid Tower (ATX / Micro-ATX / Mini-ITX)
GPU Clearance: Up to 295mm (with front fans) / 270mm (with rear fan)
CPU Cooler Clearance: Up to 160mm
Pre-Installed Fans: 4× 120mm Fixed RGB (3 Front, 1 Rear)
Max Fan Support: Up to 8× 120mm simultaneously
Fan Support: Front: 3× 120mm / 2× 140mm | Top: 2× 120mm | Rear: 1× 120mm | Bottom: 2× 120mm
Radiator Support: Front: 120 / 240 / 280mm | Rear: 120mm
Drive Bays: 2× 3.5″, 1× 2.5″ (combo) + 2× 2.5″ dedicated
Expansion Slots: 7
Side Panel: Half-View Tempered Glass
Front I/O: 1× USB 3.0, 2× USB 2.0, HD Audio/Mic, LED On/Off Button
Material: Steel + Plastic
Dimensions: 345 × 207 × 451mm (D × W × H)
Colour: Black
PSU: Not included (standard ATX)

Proudly sold by the Ringwood Digital Store.

Antec AX61 RGB ELITE ATX Gaming Case

RDSG — Fri, 10 Apr 2026 09:55:07 +0000

Geometric Mesh Front Panel Built for Airflow

The AX61’s front panel leads with purpose — a bold geometric mesh design that’s as functional as it is distinctive. Unlike solid or tempered glass fronts that restrict airflow, the high-density mesh allows cool air to flow freely into the chassis, feeding the pre-installed fans and keeping intake temperatures low. Combined with bottom air intakes, the AX61 establishes strong all-round airflow paths that support sustained performance during demanding gaming sessions. It’s a front panel that looks the part without compromising what matters most.

Four Pre-Installed ARGB Fans with Daisy-Chain Sync

Out of the box, the AX61 comes with four 120mm ARGB fans — three mounted at the front and one at the rear — covering the most critical airflow positions immediately. All four fans support ARGB lighting synchronisation with your motherboard, and the daisy-chain design allows you to link the front fans together via the main fan, keeping cable runs clean. The case supports up to eight 120mm fans simultaneously, leaving room to expand cooling capacity as your build grows.

Serious Radiator and Hardware Clearance

Despite sitting in the accessible end of the market, the AX61 doesn’t shortchange you on cooling potential. The front panel supports radiators up to 360mm, making it compatible with most 240mm and 360mm AIO liquid coolers for builders who want to go beyond air cooling. CPU coolers up to 160mm tall are supported, covering the majority of high-end tower air coolers, while GPUs up to 320mm in length fit without issue. Cable management is addressed with 24mm of clearance on the left side and 13mm on the right, keeping the interior tidy once the build is complete.

Buyer Tip: The HDD cage can interfere with longer PSUs (160mm or more in cable length). If your power supply is on the longer side, the HDD cage may need to be repositioned toward the front of the case or removed entirely to ensure a proper fit. Check your PSU dimensions before building.

Note: The ARGB fans are SATA-powered and connect to the motherboard via a SATA cable for lighting control. Ensure your motherboard has an available SATA port and ARGB header, or use the onboard LED control button on the front I/O panel to cycle lighting effects independently.

Key Highlights

Form Factor: Mid Tower (ATX / Micro-ATX / Mini-ITX)
GPU Clearance: Up to 320mm
CPU Cooler Clearance: Up to 160mm
Max PSU Length: Up to 165mm (with HDD cage) / 345mm (without)
Pre-Installed Fans: 4× 120mm ARGB (3 Front, 1 Rear)
Max Fan Support: Up to 8× 120mm simultaneously
Radiator Support: Front: 120 / 240 / 360mm | Top: 120 / 240mm
Drive Bays: 2× 3.5″, 2× 2.5″
Expansion Slots: 7
Front I/O: 1× USB 3.0, 2× USB 2.0, HD Audio/Mic, LED Control
Side Panel: Tempered Glass
Dimensions: 405 × 200 × 449mm (D × W × H)
PSU: Not included (standard ATX)
Colour: Black

Proudly sold by the Ringwood Digital Store.